Capital Sharp S designs. The good, the bad and the ugly.

Two years ago I wrote an article with suggestions on how to design a Capital Sharp S (ẞ). Now that over 400 new type families with support for this new character have been released, I thought it would be a good time to review, how the typedesigners have drawn their Capital Sharp S. At first, I present the designs I consider most successful, grouped by their design principle. There is a convention in German of naming different designs of the uppercase and lowercase Sharp S by certain cities and I am following this convention.

Design “Dresden” with a an arc at the top left

This is the design most typefaces use. It works like a capitalized form of the lowercase character (ß). But in contrast to the lowercase design it has a diagonal stroke at the top right in order to differentiate it from the letter B.

Großes Eszett

Typeface shown here: Espinoza Nova, Henriette, Ernestine, Scotch Modern, Andron, Museo Slab

Design “Dresden” with a corner at the top left

In the sample shown above, the arc on the top left is derived from the lowercase letter ß. Some designers think, that such an arc doesn’t work well within the Latin uppercase letters. So, to avoid this “lowercase look”, one could draw the top left of the Capital Sharp S as a corner. This works especially well with more geometric typefaces.

dresden-ecke

Typefaces shown here: Iwan Reschniev, Backstein, Hypatia Sans, LiebeRuth, Rooney

Design “Leipzig”

This design uses a clearly visible S as the right part of the Capital Sharp S. It works especially well with typefaces with a more calligraphic look. Very few typefaces use it, even though it is an interesting design that doesn’t cause any ambiguity problems.

leipzig

Typefaces shown here: FF Oneleigh, Numina, FF Fontesque

Design “Zehlendorf”

This is a new approach that was introduced by Martin Wenzel and Jürgen Huber within their design for the corporate typeface of the German government. They named it “Zehlendorfer Form” after the district in Berlin where their office is located. Its design falls right between “Dresdner Form” and “Leipziger Form”. It doesn’t use a diagonal stroke in the top right part, but a narrow S-like arc. The white-space and width of the character makes it very distinct. Its very legible and cannot be mistaken for a B.

Zehlendorf-Eszett

Conclusion

Up to this point in time, the design model “Dresden” is clearly the most popular one for designing the Capital Sharp S. But I would be happy to see more of the design model “Leipzig” (third letter) and “Zehlendorf” (fourth letter) in the future.

Capital Sharp S drawing models

What not to do: A rounded top right segment

Not all Capital Sharp S designs are convincing yet. The problem I have seen most is to stick too close to lowercase design of ß and give the Capital Sharp S a rounded top right part. This results in something like an “ugly B”, but cannot be read easily as sharp S (ẞ). I suggest this simple test: First, cover the left side of the letter. Now check: can the remaining right side be read as a B? Then the design should be improved.

rounded

 

What not to do: Using a double S design

I have seen several typefaces which just put SS in the slot for Capital Sharp S. This is like putting two independent V in the slot for W. Yes, there might be a historic, typographic or orthographic connection, but it’s still wrong. The Unicode slot U+1E9E was created for the character Capital Sharp S. A W is not the same as VV and ẞ is not the same as SS. If you don’t like the idea of a Capital Sharp S, you better not use U+1E9E at all. But don’t put a double S in it.

In the same vein, don’t try to create an uppercase SS ligature as Capital Sharp S. The whole point of the Capital sharp S is, that ß and ss represent a different pronunciation nowadays and without ẞ this difference cannot be maintained in uppercase-only typesetting. So an SS ligature doesn’t solve anything. It is just read as SS and not as a representation of the sharp S character.

double S

 

Tweet
Tagged as:

5 Comments

  1. Crissov 2013/11/18 at 9:31 PM #

    I like designs resembling a capital Ezh.

  2. macro 2013/11/19 at 8:27 AM #

    Why not creating a new letter as ligature from the capital SZ? For me the most logical move.

  3. Klaus 2013/11/19 at 6:53 PM #

    From a computer science point of view a ẞ serves an additional purpose: to be able to upcase and downcase a word without introducing ambiguity:
    upcase(‘aß’) → ‘ASS’; downcase(‘ASS’) → ‘ass’ [bad].
    upcase(‘aß’) → ‘Aẞ’; downcase(‘ASS’) → ‘aß’ [better].
    Similar for automatic hypenation algorithms (‘MA-ẞE’ vs. ‘MAS-SE’).
    Here using an SS-ligature for U+1E9E is better than nothing.

  4. Ralf Herrmann 2013/11/19 at 7:53 PM #

    It’s not just a “computer logic”—it’s the logic of the Latin Script since several centuries.

  5. Toshi 2013/12/03 at 1:35 AM #

    I think macro’s talking about drawing ẞ out of S and Z, not S and S. To me Dresden form is just that though.

 

Leave a Reply


*

More in Typography (1 of 95 articles)